Unit Conversion Calculator

Convert any SI or USCS unit

  • Basic or derived units

Unit Conversion Input

Unit System: /

Length



Area



Volume



2nd Area Moment of Inertia



Velocity



Acceleration



Mass



Force



Moment



Line-load



Compliance



Pressure



Density



Temperature



Angle



Unit Conversion Calculator
×

Unit Conversion Calculator

Unit Conversion Overview

Unit conversion is the process of converting a measurement from one unit system to another while preserving the physical quantity being measured. In engineering and scientific work, accurate unit conversion is essential for ensuring calculations are correct and results are properly interpreted across different measurement systems.

The International System of Units (SI)

The SI system is the modern form of the metric system and the most widely used measurement system worldwide. It is based on seven base units:

Quantity Base Unit Symbol
Length meter m
Mass kilogram kg
Time second s
Electric Current ampere A
Temperature kelvin K
Amount of Substance mole mol
Luminous Intensity candela cd
Angle radian rad

SI Prefixes

The SI system uses prefixes to indicate powers of 10, allowing convenient representation of very large or very small quantities:

Prefix Symbol Factor Example
giga G 109 1 GPa = 1,000,000,000 Pa
mega M 106 1 MPa = 1,000,000 Pa
kilo k 103 1 kN = 1,000 N
milli m 10-3 1 mm = 0.001 m
micro µ 10-6 1 µm = 0.000001 m
nano n 10-9 1 nm = 0.000000001 m

Common SI Derived Units

Many physical quantities use derived units formed from combinations of base units:

  • Force: Newton (N) = kg·m/s2
  • Pressure/Stress: Pascal (Pa) = N/m2 = kg/(m·s2)
  • Energy/Work: Joule (J) = N·m = kg·m2/s2
  • Power: Watt (W) = J/s = kg·m2/s3
  • Frequency: Hertz (Hz) = 1/s

U.S. Customary System (USCS)

The U.S. Customary System is primarily used in the United States and is based on historical English units. Common USCS units include:

  • Length: inch (in), foot (ft), yard (yd), mile (mi)
  • Area: square inch (in2), square foot (ft2)
  • Volume: cubic inch (in3), cubic foot (ft3), gallon (gal)
  • Mass: pound mass (lbm), slug
  • Force: pound force (lb, lbf), kip (1000 lb)
  • Pressure: pounds per square inch (PSI, psi)
  • Temperature: Fahrenheit (°F), Rankine (°R)
  • Angle: degree (°)

Conversion Methods

1. Multiplicative Conversion (Most Units)

Most unit conversions involve multiplying by a conversion factor. For example, converting inches to millimeters:

12 in × (25.4 mm/in) = 304.8 mm

The conversion factor (25.4 mm/in) is chosen so that the original units cancel out and the desired units remain.

2. Temperature Conversions (Offset Formulas)

Temperature conversions require both multiplication and addition because temperature scales have different zero points:

Celsius to Kelvin: K = C + 273.15

Fahrenheit to Rankine: R = F + 459.67

Celsius to Fahrenheit: F = C × (9/5) + 32

Fahrenheit to Celsius: C = (F - 32) × (5/9)

Note: For temperature differences (rather than absolute temperatures), only the multiplicative factor is used. For example, a temperature change of 10°C equals a change of 18°F.

3. Compound Units

For compound units (like velocity, pressure, or density), convert each component separately:

Example: Convert 60 miles per hour (mph) to meters per second (m/s):

60 mi/hr × (1609.34 m/mi) × (1 hr/3600 s) = 26.82 m/s

Common Engineering Conversions

Length

  • 1 inch (in) = 25.4 millimeters (mm)
  • 1 foot (ft) = 0.3048 meters (m)
  • 1 mile (mi) = 1.60934 kilometers (km)

Force

  • 1 pound force (lb) = 4.44822 Newtons (N)
  • 1 kip = 1000 lb = 4448.22 N

Pressure/Stress

  • 1 PSI = 6894.76 Pascals (Pa)
  • 1 KSI = 1000 PSI = 6.89476 MPa
  • 1 bar = 100,000 Pa = 14.5038 PSI

Mass vs. Weight

An important distinction in engineering:

  • Mass is the amount of matter (kg in SI, lbm or slug in USCS)
  • Weight is the force due to gravity (N in SI, lb in USCS)

The relationship is: Weight = Mass × Gravitational Acceleration

On Earth: Weight (lb) = Mass (lbm) × 1.0 (approximately)

On Earth: Weight (N) = Mass (kg) × 9.80665

Best Practices

  1. Always check units: Verify that units cancel properly in calculations
  2. Use exact conversion factors: Avoid rounding until the final result
  3. Maintain significant figures: Don't introduce false precision
  4. Be consistent: Use one unit system throughout a calculation when possible
  5. Document conversions: Show conversion factors in your work for clarity

References

The conversion factors used in this calculator are based on official standards from:

  • NIST Special Publication 811 - Guide for the Use of the International System of Units (SI)
  • NIST Special Publication 330 - The International System of Units (SI)
  • Federal Register Document 59-5442 - Refinement of Values for the Yard and the Pound (1959)


References

Thompson, A., & Taylor, B. N. (2008). Guide for the Use of the International System of Units (SI). NIST Special Publication 811. National Institute of Standards and Technology, Gaithersburg, MD. https://www.nist.gov/special-publication-811

Thompson, A., & Taylor, B. N. (2008). The International System of Units (SI). NIST Special Publication 330. National Institute of Standards and Technology, Gaithersburg, MD. https://nvlpubs.nist.gov/nistspecialpublication330e2008.pdf

Federal Register. (1959). Refinement of Values for the Yard and the Pound. Federal Register Document 59-5442, Vol. 24, No. 128, July 1, 1959. National Archives and Records Administration, Washington, D.C. https://www.ngs.noaa.gov/FRdoc59-5442.pdf

DISCLAIMER: The methods and calculation on aNOWysis.com are provided as means to educate the reader. There is no warranty, expessed or implied, as to the relevance or accuracy of the methods or calculations. All calculations should be checked by a qualified analyst for appropriateness and accuracy. We will not be held liable for any damages, injuries or deaths caused by using methods or calculations from this site.